Now accepting nominations for Farkle fo the Year!!!
- Thread starter slapnpop
- Start date
Help Support Yamaha FJR Motorcycle Forum:
chickey191
Well-known member
As promised - Farkle of the Year shoo in
Z's half windshield modification and support system
(he refused to wash the damned thing and the only way he could actually read a particular highway marking was to look THROUGH the windshield - resulting in ths modification )
or - maybe it was a rather large Morman Cricket
zorkler
Ave U !!!!
He must brush his hAir with that thing . So its 2 farkles in 1, that gets my vote
Last edited by a moderator:
Grievous Angel
Well-known member
Skyway's "Tipover" guards.
Probably a best seller, at least.
Probably a best seller, at least.
turbodave_98
TurboDave_98
Without a doubt Skyways's sliders, second IMHO is Cateye77 N/Line dash shelf for 06 FJR
dcarver
Well-known member
The best farkle of the year? Anyone's butt who happens to be sitting on an FJR! :bike:
Mike-H
Independent
sradek
Redbird!!
If you mean the sliders to protect the plastic, but that might break inside? .... I heard there were issues with those. Maybe corrected, but that doesn't deserve a medal. Unless I missed some posts about a permanent fix.
quicksilver
So.., how fast does that thing go?
Toecutter
What would DoG do?
Skully
Well-known member
:yahoo: [SIZE=10pt]Jestal[/SIZE]
Who says the DynoTech PowerShifter won't fit on an FJR....??? Works great. Just pulling the lever at 9000 is addictive. LOL.
I made the pieces to replace the stock link out of aluminum rod cut to length, drilled and threaded in the drill press and put together with the PowerShifter module. The little red tap at the top (in the mount) is a red tie wrap that holds and routes the wire from the PowerShifter to the PCIII. Only thing odd required to do this is the left handed tap for the lower threads on the stock rod end.
The install is a little tight as there is only about .030 clearance between the body of the PowerShift switch and the engine casting when the shift lever is moved fully to complete the shift...but it clears, that is all that really matters. It does make the rod length critical, though, when you are setting it up.
:dribble: :dribble: :dribble:
cool.
Who says the DynoTech PowerShifter won't fit on an FJR....??? Works great. Just pulling the lever at 9000 is addictive. LOL.
I made the pieces to replace the stock link out of aluminum rod cut to length, drilled and threaded in the drill press and put together with the PowerShifter module. The little red tap at the top (in the mount) is a red tie wrap that holds and routes the wire from the PowerShifter to the PCIII. Only thing odd required to do this is the left handed tap for the lower threads on the stock rod end.
The install is a little tight as there is only about .030 clearance between the body of the PowerShift switch and the engine casting when the shift lever is moved fully to complete the shift...but it clears, that is all that really matters. It does make the rod length critical, though, when you are setting it up.
:dribble: :dribble: :dribble:
cool.
TWILKIN650
Well-known member
- Joined
- Jun 11, 2005
- Messages
- 438
- Reaction score
- 1
When does voting start?
Rickster
Well-known member
Last edited by a moderator:
Thug
A shy retiring flower in a Thug's exterior
For the LAzy bastard...
Remote control door opener
Remote control door opener
Last edited by a moderator:
James Burleigh
Well-known member
Um, I beg to differ. I believe this little darling is the shoe-in:
See what wonders it can accomplish here....!
Jb
TWILKIN650
Well-known member
- Joined
- Jun 11, 2005
- Messages
- 438
- Reaction score
- 1
And the winner is?
dcarver
Well-known member
Yellow wire nuts! They get you going when your busted down in Death Valley!
JerryS
Well-known member
My vote for farkle of the year:
New iPod mounted on your handlebars, with every Isley Brother album.
New iPod mounted on your handlebars, with every Isley Brother album.
