Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Help Support Yamaha FJR Motorcycle Forum:
This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
gbrmksmith
Well-known member
·
62
·
From
Philipsburg, MT
Joined
Mar 10, 2012
Last seen
Jul 15, 2024
Messages
100
Reaction score
54
Find
Find content
Find all content by gbrmksmith
Find all threads by gbrmksmith
Latest activity
Postings
About
gbrmksmith
replied to the thread
033 Code - Engine Misfire, Down to 3 cylinders
.
Service manual troubleshooting guide says swap coils and run for 5 seconds - if no code: fixed. Then replace coil and run for 5...
Jun 1, 2024
gbrmksmith
replied to the thread
033 Code - Engine Misfire, Down to 3 cylinders
.
Original coils had issues at about 40,000 miles. Replaced with new OEM - issues again at about 80,000 miles. Third set of new OEM...
Jun 1, 2024
gbrmksmith
replied to the thread
033 Code - Engine Misfire, Down to 3 cylinders
.
Correction: 033 is for coil #1, for some reason the service manual had 033 trouble code for #1, but diagnostic side has 033 for coil 4...
Jun 1, 2024
gbrmksmith
replied to the thread
033 Code - Engine Misfire, Down to 3 cylinders
.
At 101,000 miles - coil code is back I swapped #4 and #3 coils expecting the code to switch from 033 to 032 as it would with bad coil...
Jun 1, 2024
gbrmksmith
replied to the thread
FJR Mileage Milestones
.
Just passed 100,000 miles on my current 2014 FJR
May 22, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
I tested the light on another trailer and worked fine (in the short test, at least)
May 12, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
Total weight is under 12 lbs. It can be disassembled at the two bolts on the coupler plate L side for tire replacement. That was a big...
May 12, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
Nice setup, looks like you used the back end of a motorcycle and attached at the rear tire axle. Steel or Aluminum for the hitch?
May 12, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
Wiring under the seat is complete, just need to split loom and tidy up the wires running down to the coupler.
May 12, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
Here's the "finished" hitch. Short test ride with all suspension on soft and not interferences. Tested with bike on side stand and...
May 12, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
At least a couple of times, I've taken short trips with lots of weight in the top box. Generally, on the longer road trips, it's just...
May 11, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
Yeah, didn't know about those until recently. That GIVI design is clever and certainly solves the issue by increasing the bending...
May 11, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
No, the angle of the photos don't show the clearance.
May 11, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
Getting the vertical supports to clearing the side bags and rear tire has been the most time consuming part.
May 10, 2024
gbrmksmith
replied to the thread
Cracks in the Aft SubFrame
.
Here are some photos of trailer hitch fabrication. Still need to disassemble, fully weld and paint, but gives a rough idea of the...
May 10, 2024
Loading…
Loading…
Members
Top