Audiovox cruise install, Thanks for tech tips Smitty!

Yamaha FJR Motorcycle Forum

Help Support Yamaha FJR Motorcycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

FJRCarShopGuy

Member
Joined
Jan 2, 2007
Messages
15
Reaction score
1
Had a chance to go for a test drive this past weekend after I installed my Audiovox CC. Thank you Smitty for the great tech tips, You saved me a lot of R & D time. This is one of the greatest upgrade for the FJR. It is everything you expect from a cruise control, all the functions from setting speed, maintaining speed, resume, increase/decrease speed at 1/2 mph increment worked perfectly. If anyone else is thinking about this upgrade or wondering about the audiovox CC, you will be happy with this. Great for the money!

I've kept records and lots of pics on my install. If fellow FJR owners need tech tips or support on this install, I will offer what I know and pass on the wealth as Smitty did for me. If anyone is fortunate to be close enough to have Smitty for his service, it is a great bargain. I know what it takes! Thanks again Smitty. By the way, congrats on your new job.

Gordon from S.F., CA.

 
It was great talking with you. Glad it all worked out, and happy to be able to help. Smitty

 
FJRCarShopGuy,
How much and where did you get the Audiovox Cruse Control from?

Thanks,

Violione
You can buy them from Smitty with the install, or just go to Amazon.com for about the best web pricing. You are looking for the CCS-100. Actually, I think it's the only one out there by Audiovox.

 
FJRCarShopGuy,
How much and where did you get the Audiovox Cruse Control from?

Thanks,

Violione

I paid $89.95 at amazon.com. The price as of this morning is $84.61 for the kit. You will need additional parts such as a vacuum canister and control panel bracket (which I made myself) and a button head allen bolt or a low profile bolt for the throttle pulley in order to clear the factory throttle cable.

Gordon

 
Hey Smitty, when you tap into the wires that go to the brake light etc. Do you use the scotch locks or do you strip them and solder? Jim S.

 
Hey Smitty, when you tap into the wires that go to the brake light etc. Do you use the scotch locks or do you strip them and solder? Jim S.

In the past I have used a scotch lock. But I did have a connection problem with my bike at the brake light wire. I will solder that connection from now on...Smitty

 
Had a chance to go for a test drive this past weekend after I installed my Audiovox CC. Thank you Smitty for the great tech tips, <SNIP>I've kept records and lots of pics on my install. <SNIP>

Gordon from S.F., CA.
O K Gordon, in addition to

https://www.fjr1300.info/howto/audiovox.html

for us guys & gals who are about to undertake this job, what additional tips & pixs do U have for us that will make it easier for us.

Thanks,,,De :rolleyes:

 
Had a chance to go for a test drive this past weekend after I installed my Audiovox CC. Thank you Smitty for the great tech tips, <SNIP>I've kept records and lots of pics on my install. <SNIP>

Gordon from S.F., CA.
O K Gordon, in addition to

https://www.fjr1300.info/howto/audiovox.html

for us guys & gals who are about to undertake this job, what additional tips & pixs do U have for us that will make it easier for us.

Thanks,,,De :rolleyes:
There's threads about "audiovox" and "CCS100" all over the place if you search for them. One pretty good thread about the first generation CCS100 installs was back in 2005.

 
Had a chance to go for a test drive this past weekend after I installed my Audiovox CC. Thank you Smitty for the great tech tips, <SNIP>I've kept records and lots of pics on my install. <SNIP>

Gordon from S.F., CA.
O K Gordon, in addition to

https://www.fjr1300.info/howto/audiovox.html

for us guys & gals who are about to undertake this job, what additional tips & pixs do U have for us that will make it easier for us.

Thanks,,,De :rolleyes:


Hello fellow FJR owners,

I’ve had some requests to post the highlights and areas of interests of my install. You will see below that some areas have deviated from previous installs. I’ve made some changes to streamline and or to minimize modification to the factory stuff. I hope this will help to assist those who are interested in installing the Audiovox CCS-100.

In order to remove gas tank, you will need to remove two vent hoses on the left side.

IMG_9744.jpg


Remove allen bolts in front of gas tank and loosen nut and thru bolt in back of gas tank. Do not remove thru bolt at this point, this will help you to tilt the tank in order for you to remove electrical connectors and fuel line. Notice the plastic fuel line safety securing piece that need to come off first before fuel line can be removed.

IMG_9740.jpg


IMG_9737.jpg


This is what you see with tank removed.

IMG_9730.jpg


Remove 3 bolts and frame brace.

IMG_9731.jpg


Remove heat shield.

IMG_9727.jpg


Remove air valve by loosening 3 hose clamps and electrical connector.

IMG_9726.jpg


IMG_9724.jpg


Disconnect idle speed adjustment cable from retainer grommet located below right front frame between engine and frame.

IMG_9718.jpg


Remove 2 bolts to the fuel system MAP sensor off the injector rail.

IMG_9715.jpg


Disconnect electrical connector to Injectors, MAP sensor, Throttle positive sensor etc… and move entire harness to left side of the bike and out of the way.

IMG_9721.jpg


Disconnect vacuum hoses from fuel rail assembly.

IMG_9713.jpg


Remove 2 screws and spacers securing fuel injector rail. These screws are tight, I had to use an impact driver in order not to damage them.

IMG_9714.jpg


Remove fuel injector rail with injectors, be careful not to drop the o rings at the tips of the injectors.

IMG_9712.jpg


Drill hole for 4 mm bolt to install on throttle pulley tang and install bolt and nut with lock tight. I used a spring loaded auto center punch to put a nice dimple onto the tang so my drill bit won’t wander. Do not use a regular center punch with a hammer here, you will bend the tang and it will not be aligned with the idle speed adjusting screw after. This is a small hole with little material to work with. You don’t want to drill off center here. Take your time, it may be helpful to have somebody hold the throttle open to a position for a straight shot with the drill.

Use a low profile button head allen bolt to avoid touching and or hanging up on the factory throttle cable, the clearance is very tight. Test this many times to be sure!!!!!!

As you can see from the pictures below, I did not use a button head allen bolt because I did not have one. Instead, I ground away a portion of a 4mm Phillips screw for this reason. You could do this as well, just be precise. FYI, Smitty has the correct bolt and he was nice enough to offer one to me but I was too impatient to take him up on it.

IMG_9640.jpg


IMG_9642.jpg


IMG_9645.jpg


Prepare the servo unit for installation: (sorry I don’t have pictures for the next few steps)

1) Remove the 2 screws holding the access cover in back of the servo unit and remove cover.

2) Remove main wiring harness. Note what position it came off. Although there’s a locking tang, it does not look totally fool proof.

3) Cut off and discard the separate harness (wrapped together) grey and black wires. Only cut the wires that are wrapped together and not the bigger black wire in the main connector of the servo unit harness. This is only used for vehicles with VSS (vehicle speed sensor). Since we will be operating on engine speed only (tach signal) this will not be needed.

4) Set the 7 dip switches inside the servo unit as follows: #1, #4, #7 in ON position. #2, #3, #5, #6 in OFF position.

5) Reinstall main connector and resecure cover. Make sure wires are spread out in order to have good seal.

Fabricate vacuum canister: I used 1 ½” ABS drain pipe with end caps and a brass fitting. All available from your local Home Depot or Lowes.

IMG_9669.jpg


Prepare storage tray for servo unit and vacuum canister: Notch the right side for the servo unit to sit properly. Drill small holes to accept tie straps to hold both units in place. Be careful here, the computer is mounted under tray. I removed the entire tray to avoid any chances of damaging computer. Secure servo unit and vacuum canister. Route the cable along left side of frame and back down center of engine toward throttle pulley.

IMG_9670.jpg


I made a cable guide sleeve to reduce the steep angle between the end of the servo cable to the throttle pulley. I used a piece of hard plastic automotive fuel line and used a heat gun to soften it for the bend. It fitted perfectly over the metal threaded cable end.

Cut off 7 bead of the chain and attach connectors to both ends of the chain. I used a small piece of shrink tubing over the servo cable connector after crimping as an extra precaution (it’s not in this picture).

Attach cable to throttle pulley bolt by using 2 nuts with lock tight compound.

Secure cable with supplied bracket. You will need to adjust the position for best fit and cable free play after installing the injector fuel rail and other surrounding components.

IMG_9647.jpg


Operate throttle and make sure cable/pulley combination will clear all surrounding parts without any hang ups. This is very very very important!!!!!

IMG_9651.jpg


Control switch panel wiring and mount: Skyway’s mount looks very nice, but I decided to make one like Smitty’s. I put silicone sealer at the wiring opening first and then around the opening after it was secured to the bracket. The black and grey wires are for the back lighting of the panel, the grey wire was designed to tap into a light circuit so it would light up when lights are turned on. I tied it into the red wire which is the power feed, this will cause the panel lights to stay on at all times……no harm done and I didn’t have to cut into the factory wiring. The black wire simply gets grounded to a good ground source, I found a good place on the left side brake line bracket near the steering head. I used shrink tubing to insulate the entire harness before inserting the 4 pin terminals into the white connector.

IMG_9637.jpg


IMG_9638.jpg


IMG_9664.jpg


IMG_9667.jpg


Mount the switch panel assembly and follow factory wiring routing thru opening into front of engine compartment.

IMG_9671.jpg


IMG_9672.jpg


IMG_9675.jpg


Route the green, yellow, brown, blue wires from the servo unit toward front of the bike following cable on the left side. Use wiring conduit to protect wires. The green, yellow and brown wires are cut to length and soldered back together, then the pin terminals are installed into the white connector matching colors to the control switch panel.

Power feed connection: The red wire that comes attached to the 4 pin connector with a 3 amp fuse and inline fuse holder is the power feed wire. I decided to do away with this fuse assembly and used the factory #12 fuse instead. This is for the 12 volt power adaptor located in the left compartment. I only use this for my GPS/PDA which draws very little currant so it should have no problems supporting the cruise unit as well.

I removed the fuse assembly from cruise unit, soldered a wire to length to reach #12 fuse and attached it with a scotch lock connector. This is the only scotch lock connector of the entire install. I had no choice because the length of the wiring exposed on #12 fuse was minimum. It would have been difficult to solder here. See picture.

IMG_9702.jpg


Tach signal: I didn’t want to cut into the ignition coil primary wire so I made an adaptor harness by soldering a female and a male terminals with shrink tubing insulation. I didn’t want to chance the bike running on two cylinders if this wire were to fail.

IMG_9699.jpg


Reached maxinmum images allowed. Continue on next post.

 
Cruise install continued

The factory grey with red tracer wire is connected to the male terminal and the female terminal is connected to the coil. No cutting or modifications done to factory wiring. Now you can secure and tie down wiring.

IMG_9700.jpg


Brake/tail light wiring: The purple wire from the servo unit is an important connection. It is hook in parallel to the factory yellow wire at the tail light harness located under the seat. It ground thru the brake light bulb filament when no voltage is present, in order to operate the cruise. When brake are applied and 12 volts is present, it cancels the ground and shuts off the cruise. This is a safety feature!!!!! Make sure you make a clean and secure connection here. I soldered in this circuit and used shrink tubing to seal the connection. The red wire is hooked in parallel to the factory blue wire which is the power supply for the tail light.

IMG_9705.jpg


IMG_9706.jpg


IMG_9707.jpg


Last wiring connection: The black wire with an eye bolt terminal attach from the servo unit is simply grounded to a good ground source. I used one of the seat lock latch nuts.

IMG_9680.jpg


vacuum supply and connections: I studied the hoses and vacuum sources and decided to hook into all 4 cylinders without cutting any of the factory hoses. No harm done to have 4 intake strokes in 720 degrees of crank shaft rotation vs. 1 if its hooked into only one cylinder. This will provide a much smoother and stronger vacuum. Located on the left side of the fuel injector rail is the MAP sensor (manifold absolute pressure) it is use to sense engine load for fuel mapping. This is an ideal source because it has to be accurate for fuel management. Simply use T fitting to hook in supplied vacuum hose to servo unit and route hose in the same path as the cable and wiring harness.

IMG_9715.jpg


Vacuum connection at servo unit: I used a vacuum check valve from a car (Volvo) interior climate control system. But any good vacuum check valve will work. The purpose is to retain and reserve usable vacuum during up hills or acceleration when manifold vacuum would be low. This way the cruise system has instant vacuum source when it is needed. Study the configuration and notice when vacuum drops it will lock in and retain any developed vacuum. I tested this system to hold about 14” of vacuum with the engine off.

IMG_9691.jpg


IMG_9748.jpg


Now you are ready for reassembly. In reverse order, reinstall all parts removed. You may need to adjust the servo cable position after fuel injection rail is installed for clearance and free play. There should be a slight amount of play in the beaded chain, make sure there’s no tension.

IMG_9716.jpg


Good luck on your install, any ideas, thoughts or suggestions are welcome. Please feel free to contact me with any questions.

Gordon,

Fellow FJR owner

 

Latest posts

Top