Same key for mine today. During valve adjustment check at 25,000, I took the ignition switch out myself and took it to my dealer. Only took about 15 mins to swap out the electical section. Previously, I had mine apart to resolder the red wire. Even with the new switch, I am going to install the Brodie relay.
FJRF003.1: Ignition Switch
- Thread starter Checkswrecks
- Start date
Help Support Yamaha FJR Motorcycle Forum:
BulletBrad
Well-known member
Folks, just an FYI for you. Our dealership has to keep the old switch/harness for 90 days before anything is done with it. If you have received a new set of keys with your recall work, make sure you get your old keys along with the cylinder. The dealerships HAVE to keep them awhile before they are sent back to MamaYama.
k7lvo, the pdf is considered Yamaha copyright and internal - so the forum won't post it.
KD
Big Shasta
Well-known member
I'm sorry but Ionbeam's response was horrible. It may have been a valid solution for you but that wasn't the topic. Unlike your issue MRKSFJR just got shafted by his dealer....a "workaround" isn't the answer........it's a horrible solution for someone that just got a bad repair from the dealer.
There's a big difference between factual information and RELEVANT information.
I'm just sayin.
big ears
Well-known member
My dealer says they will change the whole switch and give me another key. I questioned this quoting the letter I got and they said they would have to cut out a lot of wires and would have to charge an hour labor. Hows that sound. Golden Triangle Power Sports in Beaumont Texas. If you make them mad no telling what they will do. They scare me. :dribble:
Last edited by a moderator:
Had the ignition switch replaced today. Same key, all is well. She made it out of the shop with nothing more than greasy fingerprints all over the tank.
Feeling lucky. Got it back in 2 hours(new tire also), plenty of time to ride from Huntington Beach down the coast to San Diego and back home. Tire is now "broken in"
Feeling lucky. Got it back in 2 hours(new tire also), plenty of time to ride from Huntington Beach down the coast to San Diego and back home. Tire is now "broken in"
BulletBrad
Well-known member
Ya know KD, I'm beginning to think maybe everyone should just call Yamaha Customer Service and request a copy of the Tech Bulletin to cram down some of these "wanna-be" shops. :angry: How such a SIMPLE job can seem to be so dang hard is beyond me. We have one scheduled for next week, I'll bring in the camera and video it for YouTube. Maybe even get a few pics and put together a "How It's DUN 4 DUMMIES" for folks to print out.
Gawd, I can't even imagine what they do with a Roadstar Tranny recall. God help those poor folks. Makes me wonder if they brake with their left and shift with their right foot once they are done. <_<
I just had a little pow-wow with forum chief. Too many dealers not reading the instructions and we're going to bend things a bit IN THIS CASE. If somebody wants to PM me a link of where somebody might have a copy of the bulletin posted.....I'd make sure it gets posted for educational purposes.
Brodie
Darksider #16 - and Proud of it !
- Joined
- Sep 17, 2006
- Messages
- 1,449
- Reaction score
- 526
Hey Smoke
Here is the answer to your 2 key curse...
https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623
https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623Tumbler mix & match back to 1 key.
https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623https://www.fjrforum.com/forum//index.php?showtopic=114602&view=findpost&p=547623
Your mechanic can do this in minutes - not hours. Feel free to copy that post and take it to him. Be nice, offer to buy him an adult beverage if that's what it will take.
:clapping: Yes, It CAN Be Done!
:clapping:
Shawn,
When I fitted my spare lock into my Givi trunk I seem to remember the tumblers being the same as what you see below...
If your dealer is good they should have no problem with you "borrowing" a few individual tumblers from the recall completed switches to make the replacement saddlebag lock match your other locks.
If not "Them", I'm sure Brad may be able to help.
In fact, from what I can see all the way over here on the left coast, it seems that Brad's dealership should be your
first
choice for service instead of that other place.
Just my humble opinion
Brodie
Last edited by a moderator:
BulletBrad
Well-known member
LOL, thanks Brodie ............ I've been thinking of doing a traveling road show like on TV and have a tech ride with doing switches for folks. I already have laid hands on a few of those "NEW" lock cylinders just in case.
Hey Shawn, I'll save you some cylinder creamer for your cup of coffee complete with key-stirsticks just in case you need it. B)
Hey Shawn, I'll save you some cylinder creamer for your cup of coffee complete with key-stirsticks just in case you need it. B)
Last edited by a moderator:
v65
ouch
I would look around for another dealer. Worse case scenario Yamaha Sportscenter is within a day's reach. The owner Tony O is a respected forum member. From what you say it will be worth the trip!
Tip O' the Beenie to several forum dwellers for copies of things. I believe this link is the most direct and best quality of M2009-002R Technical Bulletin - Factory Modification Campaign of the Main Switch.Too many dealers not reading the instructions and we're going to bend policy a bit IN THIS CASE. If somebody wants to PM me a link of where somebody might have a copy of the bulletin posted.....I'd make sure it gets posted for educational purposes.
Also updated the very first post in this thread as well as several other spots in the forum. Great reading.
Admin Note:
Just remember folks that this posting is to make sure people are getting the right information. Please use it to EDUCATE dealers of the correct and full procedure for fixing recalled main switches.
HuskyRider
Well-known member
Had mine done on Friday the 20th by Roseville Yamaha, same key and they even washed my bike.
vroompuppy
Well-known member
B-B, the dealers have the service bulletin they're just not reading it! After FredW replied to my previous post in this thread with specific line #s to read I went back to my dealer's service mgr. He read the info but said he couldn't see how to get into the new ig switch without tearing it up. We settled on him calling Yamaha next week to ask their techs how to go about switching the old tumblers into the new switch. But he was apparently ignoring that part until I pushed a little. I have to say thanks again to this forum and the folks that help us all look out for ourselves a little better. I'll let y`all know how my situation turns out.
VPup
VP,
Unless you have previously replaced your ignition switch at some time in the past and have 2 keys already when you drive in to have the recall done, there is no reason to mess with the tumblers. That is far more invasive than what the recall instructions tell them to do. They should be swapping the whole lock cylinder per the procedure (see link in Iggy's post 3 posts up). However, the info Brodie posted about mixing and matching tumblers is what you'd have to do to get back to one key in that case (drove in with 2 keys).
If you read the procedure it is a very simple to swap the lock cylinders. I just don't see what they don't get. All you need to do is drill out the "security screws" under the two rubber covers to disassemble the switch assy. Those guys must be complete idiots to not be able to follow such exact instructions.
Last edited by a moderator:
Panman
Well-known member
Done on the 21st no issue's, well other than they forgot to call and tell me it was done. Saturday was a rare sunny nice day up here in great North wet!
vroompuppy
Well-known member
FredW, I think the problem was in the fact that the service mgr said that they didn't have replacement security screws to make the new ig switch whole after drilling out the new one and swapping the cylinders. And yes, I drove in with only 1 key necessary to operate all bike locks. I guess I'll need to read the tech bulletin myself to see if I can make any sense out of it. Again, we'll see how this proceeds and hopefully we can arm the next group of replacees with the appropriate info to smooth their way through the process.
VP
Guess he didn't look at the new switch very closely. From the instructions, it is clear that the security screws are already in the new switch body, installed loosely, without the heads broken off. They send them that way intentionally so they can swap the guts. My guess is the heads are still not broken off because they never removed the rubber caps over the screws to look. Because they never followed the friggen directions.
Last edited by a moderator:
I'm starting to feel better about the inclusion of a link to the actual bulletin every day.
It will be nice when dealers get up to speed.
vroompuppy
Well-known member
After reading the tech bulletin myself Fred, it is painfully obvious I'm dealing with someone who's......let's see how can I say this and not trip my warn meter.......uh, [SIZE=24pt]STUPID!!! [/SIZE]It is also obvious that until I brought it to his attention he hadn't read past line 8 or 10 or so. I'll now be very curious to see what he says after talking to Yamaha techs tomorrow; my suspicion is that my dealer will have to buy another ignition switch out of their own pocket to make things right for me. Again, I'll let y`all know. And thanks Iggy for going to bat for us and finding a copy of the bulletin that I now hope everyone reads before they go in for the recall switch replacement.
VPup
