I give, how do you remove the fairing side panels on the 2013?

Yamaha FJR Motorcycle Forum

Help Support Yamaha FJR Motorcycle Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
Yes, I agree with full compliments mcatrophy...your pics and words helped me immensley this aft while I installed the factory risers! BTW, any of you have difficulty getting those short bolts in, attaching the plastic covers to the slider steel substructure?

 
Yes, I agree with full compliments mcatrophy...your pics and words helped me immensely this aft while I installed the factory risers! BTW, any of you have difficulty getting those short bolts in, attaching the plastic covers to the slider steel substructure?
Not my words, so thank MNFJR05 for those. I would have really struggled to do my fairings without his post.

I assume you mean "installed the factory sliders"? I cheated on those, my dealer did them for me prior to my picking up the bike.

I don't know which bolts you are referring to, I had no difficulty with any, all seemed to line up ok. Sometimes if the bolt is going into one of those horrible spring-clip nuts, the nut needs to be properly positioned first. Where they are threaded into a tapped hole in the frame. it's only necessary to align everything and ensure the bolt is square to the thread.

It often helps to put a hex key through where the bolt's going to go make sure all the layers are in the right place.

If you mean the quick-fastener holding the cowling vent...

(Click on image for larger view)



... I had to grovel on the floor to see where it went, then it wasn't hard. Except for the garage floor on the back of my head
pinch.gif
.

I always put a dob of copper-loaded grease on the threads of the bolts, helps stop any difficulty the next time they are taken out.

 
Oops, my mistake 4 sure. I meant factory "frame sliders". In this case, I found the bolts along with the shouldered washers, were impossible to get threaded in order to attached the plastic shroud on the slider/support bracket. I simply could not find purchase. It appeared their simply was not enough room for both bolt and washer. Sooo, I skipped the washer and the bolts went in fine. All in all, the whole project, from headlight knob removal, cutting out a few chunks of fairing to buttoning everything up took me 4 hours. I must be slowing down in my old age. BTW, I read somewhere somebody having trouble removing one of their headlight adjuster knobs and I think I know why. While one of mine was attached by a Phillips screw, the other was a Torx of all things...minor supply glictch on the assembly line I guess !

 
Last edited by a moderator:
... BTW, I read somewhere somebody having trouble removing one of their headlight adjuster knobs and I think I know why. While one of mine was attached by a Phillips screw, the other was a Torx of all things...minor supply glictch on the assembly line I guess !
More likely the dealer, all that stuff has to be taken off to assemble the bike out of the crate. He probably lost it and found a substitute.

 
My headlight adjuster knobs fell off on the initial ride home. I suppose the assembler forgot to install the set screws. (Salesman got that straightened out in ten minutes when I returned the bike a few days later.)

As to the original question: I remove the fairing side panels by taking my bike to the dealer. In the past 15 years, I have somehow become terribly clumsy with tools. I tried to remove the right side (starboard) to wire up the aftermarket horns. An hour later, after having actually removed zero panels, I had the fairing somewhat back together, two leftover screws, and one lost bolt. Not trying it again.

 
Last edited by a moderator:
After reading this, I've made the executive decision to have my competent dealer replace my damaged left side plastics since insurance included the cost of labor. That way if something goes wrong or pieces are broken, they will be responsible instead of me!

 
... BTW, I read somewhere somebody having trouble removing one of their headlight adjuster knobs and I think I know why. While one of mine was attached by a Phillips screw, the other was a Torx of all things...minor supply glictch on the assembly line I guess !
More likely the dealer, all that stuff has to be taken off to assemble the bike out of the crate. He probably lost it and found a substitute.
I'm not sure about that.Seems to me, most of the bike, especially that area of the bike, comes assemled Watching all those shows about the bike industry and seeing the various brands and models coming off the assembly line, me thinks motorcycles come more assemled than most peple know, with alldue respect of course!

 
... BTW, I read somewhere somebody having trouble removing one of their headlight adjuster knobs and I think I know why. While one of mine was attached by a Phillips screw, the other was a Torx of all things...minor supply glictch on the assembly line I guess !
More likely the dealer, all that stuff has to be taken off to assemble the bike out of the crate. He probably lost it and found a substitute.
I'm not sure about that.Seems to me, most of the bike, especially that area of the bike, comes assemled Watching all those shows about the bike industry and seeing the various brands and models coming off the assembly line, me thinks motorcycles come more assemled than most peple know, with alldue respect of course!
Pictures I took of my bike prior to it being fully assembled include this one (apologies for the quality, they were snapped with my phone)

(Click on image for larger view)



It shows the righthand dash area uncovered, you can see the headlamp adjuster spindle without its knob just left of centre. The bike comes without its mirrors fitted, these panels have to come off in order to fit them.

More pictures start here.

 
Last edited by a moderator:
Because there seem to be many accesses to my pictures associated with fairing removal, I've created a pdf file based on my entry above.

It includes the text and pictures in a form that can be printed, and may be more convenient for taking into your work area.

The file is over 30MB long, so will take a little while for you to download due to my slow server internet connection, probably over twenty minutes, so apologies for that.

[edit] The file size is about 3MB [/edit]

Direct link: https://atrophy.lock.net/do/FJR2014PanelRemoval.pdf.

I hope this is useful. Any errors or other comments, please let me know.

 
Last edited by a moderator:
Downloaded and saved! Thanks mcatrophy from current [and future!] GEN III owners.

I'll be digging into my first GEN III this weekend for a LED light install, perfect timing!

--G

 
I completed the fairing removal without breaking anything thanks to the guidance provided by MNF JR and mcatrophy. While I went into it with some trepidation, I found the whole experience not as bad as some have let on. In order to accomadate the OEM Frame sliders, the fairing plastic had to be modified (also read: cut). Once I found the proper speed on the Dremel like tool, even that was reletively easy. All in all, I was worried about nothing. Had no parts left over and didn't lose anything. Thanks once again to those Forum members that have given us the pics and instructions on how to`s re: fairing removal.

 
This information will be very helpful to me as I am just now learning about the Gen III.

Am I to understand that the fairings have to be removed to install frame sliders?

Me thinks I'm going to buy every thing and do this only once (frame sliders, LED lights, fuse block and accessory wires, etc)

 
This information will be very helpful to me as I am just now learning about the Gen III.Am I to understand that the fairings have to be removed to install frame sliders?Me thinks I'm going to buy every thing and do this only once (frame sliders, LED lights, fuse block and accessory wires, etc)
OEM sliders need the fairings off. Don't know about any others.

 
Yes, BIG THANK YOU to those that contributed. mcatrophy's PDF will be quite valuable over the next few months as I route wiring to new GPS and cell phone mounts.

 
Top